Hyperion 40CH 5.8gHz 25-200mw Micro 20x20mm FPV VTX w/ Integrated OSD

1 Review | Write a Review | Hyperion | HP-FP25200VTXOSD

 

Hyperion quality products!

 

Part Number: HP-FP25200VTXOSD

 

Product Description

The Hyperion 5.8GHz Selectable 25mW / 200mW Video Transmitter is built on Hyperions extensive knowledge of FPV racing and capabilty to produce a micro size VTx with selectable RF power. A must have for those looking to get into FPV Race. The Hyperion Adjustable RF Power (25 - 200mW) 5.8GHz 40CH FPV video transmitter is the ultimate FPV VTX giving you the option to adjust output power to fit your needs. This transmitter features the ability to adjust the transmission power, from 25mW and 200mW for long range. The lower 25mW transmission power means more pilots can fly together without overpowering each other on close frequencies. Whilst the 200mW allows long range outdoor flights.

The VTX features an easy to use single button, LED interface. It also comes with a clean pre-wired harness, and only weighs 12g. It’s perfect for a wide range of aircraft! This VTX transmits a full range of 40 channels and features integrated OSD so that you can see all the flight information on your screen. Perfect for 250-size Quad racers!

Supports most brands of equipment and has guaranteed compatibility with all of the ImmersionRC, Fatshark recievers and includes the new Raceband frequencies too.

Features:

  • 40 channels: Cover A, B, C, D, and E bands
  • Micro sized and light weight
  • Transmitter frequency: 5645-5945MHz with 25mw/200mw power output
  • Transmitting distance > 25mw: 25-60m / 200mw: 100-300m (open area)
  • Integrated OSD

Included with the package:

  • 5.8Ghz AV transmitter x 1
  • 5p cable w/JST Connector x 1

 

Specifications:

  • Modulate: Wideband FM Modulate
  • Video Format: NTSC/PAL
  • Output Impedance: 50 Ohm
  • Output Power: 25mw 12-14dBm / 200mw 23-24dBm
  • Channel: 40 CH
  • Supply Current: 70/200mA
  • Video Band Width : 0~8.0 MHz
  • Audio Carrier Frequency: 6.5 MHz
  • Video Input Level: 0.8~1.2 Vp-p
  • Video Input Impedance: 75 Ohm
  • Audio Input Level: 0.5~2.0 Vp-p
  • Audio Input Impedance: 10K Ohm
  • Connector: RP-SMA Male Jack
  • Antenna connection: RP-SMA Female Jack
  • Dimension: 20mm x 20mm
  • Weight: 12g (without antenna)

 

Compatible with Fatshark, ImmersionRC, Boscam, Foxtech and other generic branded FPV receivers within the same frequency range.

*Note: This VTX is 25mw / 200mw output power selectable. By default this VTX will transmit in 25mw. To transmit in 200mw output you must cut the output change wire. For more details review the manual in “Manuals and Support” section.

*Note: TX antenna must be installed properly before it is switched on, power on without install antenna, or a improper antenna was used may easily burn the TX, and such damage is not covered by warranty. FPV Regulatory Notice The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a ""HAM"" amateur radio license if you transmit in the 200mw output mode. Learn more about HAM licenses. It is your responsibility to ensure that the use of this product meets the requirements imposed by your governments rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. AirCraft-World.com cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

 

Reviews

  • 博之 久保

    小型で出力電力切り替えできて、OSDも付いていて、機能はとても良いのですが、OSD設定のため200mw設定で5~分程度使用していたら、画像が出なくなりました。回路の発熱による損傷と思われます。初期不良かと思いましたが、同じ症状で2個目も壊れました。OSDの画面も、つなぐカメラによっては表示が切れてしまいます。

Leave a Review