visit Air Craft website

Air Craft
DataSheet

 HYPERION
Z-2205
Specifications

Hyperion Z22-Series Outrunner General Information Here
See General Guide for Brushless Motor/Controller installation here

News: Z2205-46 data is added. Note -34, -38 data is updated.
  HP-Z2205-34 HP-Z2205-38 HP-Z2205-46
Stator Diam. mm 22 22 22
Magnet Length mm 5 5 5
Weight g 29.4 29.4 29.4
Outside Diameter mm 28 28 28
Length mm 33 33 33
Output Shaft Diameter mm 3 3 3
Mount Screw Diameter mm 3 3 3
Max eff. Current A 5-8 4-7 3-6
Peak current A 11 9 8
LiPo cells 2~3 2~3 2~3
NiMH & NC cell 6~10 6~10 6~10
Winding 34T 38T 46T
Resistance Ohm 0.150 0.178 0.245
Io A 0.58 0.56 0.42
KV rpm/V 1530 1370 1200
Recommended ESC HP-TITAN-10P HP-TITAN-10P HP-TITAN-10P

A DC Power supply was used for testing.  You can approximate the voltage a battery pack will produce using this chart for cell counts.  The chart assumes that the battery is being used near rated current limit.  Using a pack with higher capacity cells may result in higher voltage, rpm,  and current draw. Appearance in the data does not mean the prop and voltage combination is necessarily recommended;  see rated max efficient and maximum current specs above.
 
PS V Li-Po NiMH
6.7V 2S 6N
7.7V na 7N
8.8V na 8N
9.9V na 9N
10.1V 3S na
11V na 10N

 
 
HP-Z2205-34
Power Source Prop Volts Amps RPM Watts
600W PS APC7x5SF 6.7 8.1 8565 54
    7.7 10.1 9360 77
  APC8x3.8SF 6.7 10.3 7560 69
  GR7.5x4 Fold 6.7 8.4 8340 56
    7.7 10.5 9150 80
ET-HPV2-0700-2S APC7x5SF 6.65 7.8 9210 52
ET-HPV2-1250-2S APC7x5SF 7.04 8.6 8880 60
600W PS APC5.1x4.5 E 6.7 4.6 9540 31
    7.7 5.5 10740 42
    8.8 6.7 11970 59
    9.9 8.2 12990 81
    10.1 8.6 13200 87
    11 9.6 14190 105
  APC6x4 E 6.7 4.3 9570 29
    7.7 5.4 10830 42
    8.8 6.7 12120 59
    9.9 7.9 13260 78
    10.1 8.2 13440 83
    11 9.3 14280 102
  GR6x3 Fold 6.7 5.3 9060 36
    7.7 6.5 10230 50
    8.8 7.9 11310 70
    9.9 9.6 12270 95
    10.1 9.9 12510 100
ET-HPV2-0700-2S APC7x5SF 6.51 7.2 8220 47
ET-HPV2-1250-2S APC7x5SF 6.95 8 8610 56

 

HP-Z2205-38

        
Prop Volts Amps RPM Watts In
APC 7x5SF 6.7 5.8 7890 39W
  7.7 7.2 8715 55W
  8.8 9.1 9600 80W
APC 8x3.8SF 6.7 7.7 7035 51W
  7.7 9.2 7650 71W
GR 7.5x4 Fold 6.7 6.4 7695 42W
  7.7 7.9 8580 61W
  8.8 9.5 9480 83W
GR 8x4.5 Fold 6.7 8.2 7110 55W


Z2205-46

This motor is intended specifically for 3-Cell E3D with GWS 8x4DD (aka HD) prop, or Two-cell E3D with APC 9x3.8 or GWS 9x4.7.  You can see that it would also make a super sport motor, turning the GWS 7x3.5DD at nearly 12,000 rpm on only 52 watts!! Max recommended continuous currrent is 6A, with short-time peak at 7.5A.  Do not run Slowfly type props on 3S.
 
HP-Z2205-46 Initial Prop Tests
Battery Type Prop V A RPM Watts In
ET-HPV2-700-2S GWS 7x6 SF 7.3 5.4 6660 39.4
  GWS 8x4.3 SF 7.2 5.1 6705 36.7
  GWS 9x4.7 SF 6.8 6.7 5295 45.6
  GWS 9x5DD 7.0 6.0 5865 42.0
           
ET-HPV2-700-3S GWS 7x3.5DD 11.3 4.6 11790 52.0
  GWS 8x4DD 10.7 7.5 9630 80.3

 

Z-2205 Series Data          Z-2209 Series Data         Z-2213 Series Data

See General Guide for Brushless Motor/Controller installation here