visit Air Craft website

Air Craft
DataSheet

 HYPERION
Z-3025
Specifications


Hyperion Z30 Series Outrunner General Information Here
  HP-Z3025-06 HP-Z3025-08 HP-Z3025-10 HP-Z3025-12
Stator Diam. mm 30
Stator Length mm 25
Weight g 186
Outside Diameter mm 37
Length mm 50
Output Shaft Diameter mm 5
Mount Screw Diameter mm 3 3 3 3
Max eff. Current A 40-60 32-42 27-37 20-30
Peak current A 65A 60sec
100A 10sec		 52A 60sec
65A 10sec		 46A 60sec
54A 10sec		 38A 60sec
42A 10sec
LiPo cells 2~3 2~4 2~4 2~5
NiMH & NiCd cells 6~9 6~12 6~12 7~16
Winding 6T 8T 10T 12T
Resistance Ohm 0.0102 0.0175 0.0250 0.0360
Io A 3.6 3.2 2.3 1.79
KV rpm/V 1365 985 815 665
Recommended ESC HP-TITAN-50P
HP-TITAN-80P		 HP-TITAN-50P
HP-TITAN-80P		 HP-TITAN-50P
HP-TITAN-80P		 HP-TITAN-50P
HP-TITAN-80P

A DC Power supply was used for most testing.  You can approximate the voltage a battery pack will produce using the chart belowfor cell counts.  The chart assumes that the battery is being used near rated current limit.  Using a pack with higher capacity cells (or very "High C" types) will result in voltage, rpm,  and current draw which could be 20% higher. Use an ammeter like the Hyperion Emeter to check current before flight!

Appearance in the data does not mean the prop and voltage combination is recommended;  see rated max efficient and maximum current specs above.
 
Lipo/1Cell :3.35V  
Nicd/1Cell :1.1V  
Lipo 2S 6.7V 6N
  7.7V 7N
  8.8V 8N
  9.9V 9N
Lipo 3S 10.1V  
  11V 10N
  12.1V 11N
13.2V 12N
 Lipo 4S 13.4V  
  14.3V 13N
  15.4V 14N
[note: June 6] Mr. P. Connolly has done some tests using 7 and 10-cell NiMH packs for the Z3025-06 and Z3025-08, so those are given as "cells" in the voltage column below.  Where a voltage is given, test were done on our power supply, so use the chart above to approximate cell counts.

Z3025-06 is specifically intended for 7-Cell LMR glider competition (or 2S Lithium sport glider use). Props 12x6 to 15x10 may be used, depending on whether you are in competition, or just having fun.  Performance is rather astounding - matching Hacker B40 6L +4.4:1 Maxon gearbox motors in efficiency of about 80% at 70A, while weighing nearly 40 grams less and costing about 40% of the price.  Very nice in 1.4~1.6M Hotliners with 11x8 prop on 7~8 cells, too.

The Z3025-06 can also do duty in an IC engine 25-Class to 40-Class models with 3S lithium and APC SPORT 9x5 to 9x6 props. We do not recommend "E" props for this motor on 3S lithium. Battery should be rated for 38 to 45A continuous depending on prop.

GP-3300NiMH were used in the Z3025-06 folder tests below.
NOTE:  Some users report much higher current (up to 20A Higher!) and rpm with GP-2200 and 3800.  Test batteries may have been tired... so fit prop and check current with your batteries!

HP-Z3025-06 Prop Data
Prop Volts Amps RPM Watts
GR12x6 Fold 7-cell 47.1 7905 350
GR14x9.5 Fold 7-cell 63.4 6300 410
 APC 9x5 SPORT 3S 34 12810 343
APC 10x5 SPORT 3S 44 11480 444

Z3025-08 is excellent as motor for sport gliders 2~2.5M on 7~9 cells with props 12"~14".  Choose prop/battery to achieve 50A or less if runtimes will exceed 20 seconds.

On 3S lithium rated for about 40A continuous or higher, the Z3025-08 is a superb motor for sport models from about 1Kg to 2.5Kg, depending on type.  In the Hyperion P-51 Mustang 25, which weighs about 1.5Kg with retracts and scale spinner, the motor provides exciting speed and very strong climbs at only 327W on APC "E" 10x7 prop.  With the 10x10 APC "E", it is 'blazing' fast.....

Max prop size on 3S for an E3D models should be 12x6E.  For 4S, limit prop to APC SPORT 11x4 maximum (do not use "E" prop on 4S).

HP-Z3025-08 Prop Data
Prop Volts Amps RPM Watts
APC8*6 E 10-cell 21.4 10410 240
 APC10x5 E 13.4 34.8 11190 466
7-cell 15.9 7710 132
10-cell 27.0 9930 296
 APC10x7 E 3S 31.2 9190 327
 APC10x10 E 3S 42.1 8480 440
 APC12x6 E 6.7 17.8 5700 119
  10.1 36.4 8010 368
7-cell 27.1 6900 214
10-cell 40.5 8370 404
 APC13x6.5 E 6.7 23.3 5490 156
7-cell 32.7 6345 249
 APC14x7 E 6.7 29.0 5175 194
7-cell 40.6 6030 308
GR14*9.5 7-cell 43.6 5640 318

HP-Z3025-10 is primarily intended for thermal gliders using large folding props, for E3D models on 3S, and sport models on 3S or 4S lithium. Max prop size on 3S for an E3D models should be 13x6.5E.

HP-Z3025-10 Prop Data
Prop Volts Amps RPM Watts
APC11x5.5 E 3S 22.7 8140 240
  4S 35.3 10220 480
APC12x6 E 3S 31 7740 324

HP-Z3025-12 is primarily intended for thermal gliders using large folding props, for E3D and sport models on 4S lithium.

HP-Z3025-12 Prop Data
Prop Volts Amps RPM Watts
APC13x6.5 E 3S 26 6400 265
  4S 38 7980 550
APC12x6 E 4S 30.5 8540 435

Z-3007 Series Data      Z-3013 Series Data      Z-3019 Series Data